Car Alarm & Security

12V 3 Inch X5 Colorful OBD2 HD HUD 3 Inch Screen 9V to 16VPrompter Monitor Vehicle PC Alarm Detector Description: 1. Models automatically adapt to meet OBD II or EUOBD (automatic vehicle diagnostic system) models and Play; 2.3 Inches HD display; 3. Polychromatic color design, so that the screen is more abundant, easier to read; 4. The use of nano technology to eliminate unwanted reflections sharper pictures; 5. The display rich content: speed, engine speed, water temperature voltage instant fuel consumption, average fuel consumption, mileage measurement, shift reminding fatigue driving reminders, low voltage alarm high water temperature alarm, speed alarm, engine fault alarm, eliminate the fault code freely switch kilometers miles; 6. Switcher, vehicle start, lorry shutdown, effectively protect the car battery; while retaining the manual switch mode, more conducive to control HUD; 7. Automatic and manual brightness adjustment mode, driving without glare. Specification: Ambient Temperature - 40 ~ + 80 Atmospheric 86 ~ 106KPa Relative Humidity 10% ~ 95% Environmental Noise 60dB (A) Alarm Sound Level 30dB (A) Operating Voltage DC 9V ~ 16V (DC 12V / 400mA) Product Dimensions 9 * 5.4 * 1.2 (cm) Product Weight 40g HUD preparation before installation and use: 1. Know your car brand, at the time of purchase HUD to choose line with OBD II (or EU OBD) standard models for proper use, open the hood and look for the sticker below, if you have the words of OBDII CERTIFIED can be installed (Figure 1) check the bottom of the steering wheel have no car diagnostic socket (domestic car in 2007 after most of the car assembly). 2. Find the 16-pin diagnostic socket of the vehicle with OBDII cable with contact. HUD initial use Car name engine. HUD switch opens, showing the current vehicle voltage then enter the search car computer version of the state, if the HUD showing speed, rpm, indicates that the product has been installed successfully. (After 1 minute, or if the display voltage only then, check HUD hosts, OBD Interface OBD data line, the vehicle is properly connected, and make sure the connection is stable and reliable. Open HUD host power switch, start scanning again) HUD solutions to common problems: 1. the screen without any display. Without electricity Reason: start the car engine, check the OBD cable is connected to the elastic, pull down repeatedly insert multiple times, check HUD master switch is turned on. If you still do not show is recommended for test vehicles, whether cars OBD diagnostic interface is bad analysis, if the OBD diagnosis bad, it is recommended to maintain good OBD interface, HUD connection again, you can normally use 2. powered on, but the screen only displays cars voltage, automatically turns off after 30 seconds. Cause: HUD product is only suitable for OBDII and EOBD interface Automobile production year (US Department of 2003, the other regions after 2007, began using OBDII and EOBD) HUD Products Support OBD I and JOBD 3. After the car is turned off, will not automatically shut down, Cause: HUD automatic shutdown value is set to 13.2 volts, automotive voltage higher than 13.2 volts, automatic boot, lower than 13.2 volts, automatic shutdown, not shut down, then the item 7 parameter settings value adjusted 135, or a little higher, Do not be too high, preventing the car voltage reach the starting voltage can not be switched 4. not clear and ghosting sunlight. Solution: Check the HUD protection film on whether the host has torn, a reflective film on the box attached to the corresponding reflective glass HUD 5 wrong operation lead to crashes. Be reply to factory settings, HUD after connecting car, start the car, Dial key live dial five seconds, HUD full bright display, namely to restore factory settings, and then on the dial 5 seconds, return to display the page 6. speed allowed. Countermeasures: Under a power-up, the vertical press dial button for 5 seconds to enter the menu options, the menu display 0, the parameter value 107, a difference of how much, or allocated on the dial and according to your dashboard, increase and decrease the speed difference value. Exit After adjustment, dial key vertical press 5 seconds 7 speed alarm. Solution: The default alarm speed is 120 If you want to transfer large or small alarm tone, Under a power-up, the vertical press dial button for 5 seconds to enter the menu option, short display 6, the parameter value of 120 indicates the speed 120 alarm, or allocated on the dial, increase and decrease, adjusting the press many times the menu, dial Exit 5 seconds after pressing the round key vertical 8. How to restore factory settings: HUD After connecting car, start the car, Dial key live dial five seconds, HUD full bright display, namely to restore factory settings, and then on the dial 5 seconds, return to display the page. Package Included: 1 X Displayer 1 X OBD Cable 1 X Mat 1 X Protect Film 1 X Manual

X3 5.5inch Car HUD Head Up Display with Bluetooth Function OBD2 Interface Plug This HUD built in ELM327 and with bluetooth version function. Not only you can use the HUD to read all the information on windowscreen, but also you can download OBD APP from Android phone to read more information. The methods are below: 1. Download OBD App from phone 2. Open bluetooth of phone to scan,when display"HUD bluetooth" click connect. The password is 1234 3. Open OBD App, click setting and adapter to connect 4. When finish connection,back to OBD APP interface to read more information. Feature: 1.Plug and play. HUD can automatically adapt to vehicle type which in line with OBDII or EUOBD(On-Board Diagnostic System). 2.Comprehensive display. HUD can display many parameters at the same time as follows, vehicle speed, engine speed, water temperature (voltage, throttle valve position, ignition advance angle, time of 100 km acceleration),fuel consumption, mileage, low fuel tips, engine failure. 3.Three display mode. Driver can chose normal display mode, high- speed display mode and automatic display mode. 4.Free switch. Km and mile can be switched freely. 5.Suitable size. The display area is 5.5 inches which is very clear for driver to read data. 6.Automatic power on and off. Starting with the vehicle starting, stopping with the vehicle stopping to protect the vehicle's battery. Moreover, HUD can alsopower on and power off by manual, which is more easy to control HUD. 7.Flexible alarm mode. HUD can offer single-stage and four-stage overspeed alarm modes to choose to make driving safer. 8.Engine speed alarm. It contributes to shift gear in time to save fuel also has significance to new driver. 9.Flexible brightness adjustment. The brightness can be adjusted automatically or manually to reach the best state which is in harmony with the environment. Specification: 1. Service conditions: Environment temperature: -400 ~ +800 Barometric press: 86 ~ 106 KPa Relative humidity: 10% ~ 95% Environment voice: 60 dB(A) 2. Alarm of sound level: 30dB(A) 3. Work voltage: 9V~16Vdc(12Vdc/400mA) 4. Size of product: 150 * 85 * 14 (mm) 5. Weight of product: 278g (including the giftbox) Package Included: 1 X X3 Car HUD Display 1 X OBD II Interface 1 X English User Manual

Car Auto Meter Trio Ammeter Water Temp Oil Pressure Gauge Mechanical Sliver Feature: Universal machine. Sliver metal bracket,sliver bezel. Have it, you have the equivalent of an ammeter, water temperature and oil pressure gauge. Specification: Color: Sliver Face Weight:477g Size:19cm x 7.5cm(Length and width) Packagesize: 9cm x 8cm x 24cm(Length x width x height) Note: Instruction is not included. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. Package Included: 1 X Oil Pressure 1 X Water Temp Gauge 1 X Ammeter 1 X Three Hole Gauge Bracket

New Front/Rear Parking Sensor For HONDA CR-V 2007 2008 2009 2010 2011 2012 39680-SHJ-A61 Black Descritpion: This is general model that fit for Honda CRV series car such as CR-V 2007, 2008, 2009, 2010, 2011, 2012, it could be a replacement for your original car reverse sensor once yours broken. This is model with black color, and could be paint to any colour to fit your car color. Installation with good quality and high sensitive design. Specification: Colour: Black Use position: Front/Rear OEM Number: 39680-SHJ-A61 Pin Quantity: 2 Size: Sensor Diameter 26mm Install Position: Frant and Rear Bumber are avaiable Applicable Car: HONDA CR-V 2007, 2008, 2009, 2010, 2011, 2012 Package Include: 1 X Parking Sensor

U903I Car TPMS Tire Pressure Monitoring System Cigarette Lighter Supply Power 4 Interna Sensor New Model Specification: Displayer Parameter: Working Temperature:(-20C- +85C) Storage Temperature:(-40C- +125C) Input Voltage:DC8V-16V Transmitting Frequency:433.92MHz Size( L*W*H )mm:80*30*12mm Sensor Parameter: Working Temperature:(-40C- +125C) Storage Temperature:(-40C-+125C) Pressure Range:0-116psi(0-8bar) Pressure Precision:1.5PSI(0.1bar) Temperature Precision:3C Transmitting Power:<10dbm@50 Transmitting Frequency:433.92MHz Battery Life:>5 years Size( L*W*H )mm:60*32*15mm Weight: 29g Package Includes: 1 X Cigaratte Lighter Supply Power TPMS 4 X Internal Tire Pressure Sensor

12V AW010 JP-D68 433.92MHz Car Sercurity Alarm System with 2 Pcs Remotes Description: 1. Remote arm / disarm 2. Silent alarm / re-arm 3. Arming reminding 4. Automatic arm optional 5. Remote trunk release 6. Anti-hijacking 7. Vibration record 8. Power off memory 9. Urgent disarm / urgent call 10. Car finding / help calling 11. Two stage shock sensor 12. Trigger warning identification 13. Central door lock automation 14. Door unlocked well warning 15. Dome light delay automatically 16. Pneumatic / electronic lock optional Specification: Package Included: 1 X System 2 X Remote Controls 1 X LED Indicator 1 X Engish manual 1 X Alarm Horn 1 X Set of Cable

AW010 JP-D68 433.92MHz Car Sercurity Alarm System with 2 Pcs Remotes Description: 1. Remote arm / Disarm 2. Silent Alarm / Re-arm 3. Arming Reminding 4. Automatic Arm Optional 5. Remote Trunk Release 6. Anti-hijacking 7. Vibration Record 8. Power Off Memory 9. Urgent Disarm / Urgent Call 10. Car Finding / Help calling 11. Two stage shock sensor 12. Trigger warning identification 13. Central door lock automation 14. Door unlocked well warning 15. Dome light delay automatically 16. Pneumatic / electronic lock optional Specification: Package Included: 1 X System 2 X Remote Controls 1 X LED Indicator 1 X Engish manual 1 X Alarm Horn 1X Set of Cable

E300 Car HUD Head Up Display 5.5 inch with OBD OBD2 Interface Plug HUD Main Feature: 5.5" screen. 2D visual effect. Auto power on and off with the vehicle. Automatic and manual brightness adjustment mode. Plug and Play connectivity with any OBDII or EUOBD capable vehicle. Multi colour design makes the screen easier to read highlight important details for quick viewing. The use of nanotechnology to eliminate unwanted reflections making the information easier to read. Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time,mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometre/mile. HUD Installation Procedure: 1. Ensure your vehicle is OBDII compatible or EUOBD. a. Check around the area under the steering wheel for an OBD plug b. Contact your vehicle manufacturer or search online c. Open the bonnet and look for a OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn't a deciding factor) 2. Locate the 16 pin diagnostic link. This is usually located in the area under the steering wheel. 3. Start vehicle's engine and ensure power switch is in the on position. 4. HUD will power on with engine a. If the HUD displays vehicle voltage, fuel consumption, speed and rotational speed the unit has installed correctly. b. Failing the above: Wait up to one minute for software to sync and confirm OBD cable is plugged in properly. Reflective Film Installation: 1. Place the supplied non-slip mat in the desired position on the dashboard with the HUD on top. 2. Observing where the HUD reflects place the reflective film in position. a. Ensure the surface is clean and dry before installing the film; b. Remove the back protective side marked (1) and attach the film to the clean windscreen; c. Once you're satisfied with the location use a credit card or similar to remove any bubbles or air pockets that remain; d. Remove the front side marked (2) if you need to adjust the HUD's reflection, reposition using the nonslip mat. Technical Parameter: Environment Temperature -40 ~ +80 Barometric Press 86 ~ 106KPa Relative Humidity 10% ~ 95% Environment Noise 60dB Alarm Decibel 30dB(A) Work Voltage 9V ~ 16Vdc(12Vdc/400mA) Product Dimensions 12.5 * 7.5 * 1.5(cm) Product Weight 110g Package Included: 1 X E300 Head Up Display 1 X Reflective Film 1 X OBD Connecting Line 1 X User Manual

Car Vehicle Alarm Protection Security System Keyless Entry Siren Remote Control Feature: 1. Remote arm / disarm 2. Remote silent alarm 3. Remote trunk release 4. Anti-hijacking 5. Power off memory 6. LED indicator status 7. Urgent disarm / urgent call 8. Car finding / help calling 9. Central door lock automation 10. Door unlocked well warning 11. Electronic lock / pneumatic lock 12. Positive / negative trigger optional 13. Remote control and Main unit match code: When a remote control is lost or out of work, you can re-learn the code. (Method: open the side door, slam the foot brake, directional lights flashing, open ACC.ON-OFF(five times),and stopped in the open position, directional lights stop flashing. At this time, press any key on the remote control to learn code. speaker calls out, indicating success in learning.) Specification: Main Unit: 1. Voltage: 12V+/-3V 2. Static current: 10mA 3. Output current: turning light 7.5A x 2 4. LED Indicator:3mA 5. Siren:10A 6. Central locking:10A 7. Operating frequency: 315MHz-433.92 MHZ Remote Control: 1. Voltage: 12V 2. Static current: 0mA 3. Battery:CR2016(Included) Shock Sensor: 1. Working voltage:DC12+/-3V 2. Static current:1mA Package Included: 1 X Main Control Unit 1 X LED Connection Wire 1 X Engine Killer Relay 1 X Shock Sensor 1 X Wiring Set 1 X English User Manual 1 X Siren 2 X Remote Control

Air Line Tyre Inflator & Pressure Gauge 10-120PS Heavy Duty-Pro Tool Black Hose Specification: Material: Material & Rubber Length: 52cm Air Inlet Size: 1/4" Other Size: As the picture shown Color: Black Quantity: Pack of 1 Feature: Tyre air inflator Easy to read gauge Gauge measures 10-120PSI in 2lb increments 12 inch heavy duty rubber hose Easy to attach to valves 6 inch chrome plated steel dual chuck Fitment: Fits for light truck and bicycle tires Note: Please check the size measurement chart carefully before making a payment. Please allow 0.1-0.5cm difference due to manual measurement. The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding. Instruction is not included. Package Included: 1 X Gauge

Car Central Alarm Protection Security System Remote Control Keyless Entry Siren Feature: 1. Remote arm / disarm 2. Remote silent alarm 3. Remote trunk release 4. Anti-hijacking 5. Power off memory 6. LED indicator status 7. Urgent disarm / urgent call 8. Car finding / help calling 9. Central door lock automation 10. Door unlocked well warning 11. Electronic lock / pneumatic lock 12. Positive / negative trigger optional 13. Remote control and Main unit match code: When a remote control is lost or out of work, you can re-learn the code. (Method: open the side door, slam the foot brake, directional lights flashing, open ACC.ON-OFF(five times),and stopped in the open position, directional lights stop flashing. At this time, press any key on the remote control to learn code. speaker calls out, indicating success in learning.) Specification: Main unit: 1. Voltage: 12V+/-3V 2. Static current: 10mA 3. Output current: turning light 7.5A x 2 4. LED Indicator:3mA 5. Siren:10A 6. Central locking:10A 7. Operating frequency: 315MHz-433.92 MHZ Remote controller: 1. Voltage: 12V 2. Static current: 0mA 3. Battery:CR2016(Included) Shock Sensor: 1. Working voltage:DC12+/-3V 2. Static current:1mA Package Included: 1 X Main Control Unit 2 X Remote Control 1 X LED connection wire 1 X Engine Killer Relay 1 X Shock sensor 1 X Siren 1 X Wiring set 1 X English user manual

Display for Starline A61 LCD Two Way Car Alarm System Specification: Model Name: A61 Item Type: Alarm Systems & Security Special Features: LCD display for two way car remote External Testing Certification: FCC Item Width: 2.5 cm Item Length: 4 cm Item Weight: 0.01 kg Connection: Metal feet Note: 1. We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. 2. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 3. Instruction is not included. Package Included: 1 X A61 LCD Display

Universal Car Portable Multi-function Car Tire Pressure Flashlight Function: 1, Flashlights, emergency use; 2, Tire pressure gauge, ensure the correct tire pressure, prevent puncture to ensure road safety; 3, Life-saving hammer, escape use; 4, Seat belt cutter quickly cut the seat belt, so that security is more assured. Specification: Model: HF-818F Power Type: Battery Power: 1W Light Source: LED Battery capacity: 500ML Package Included: 1 X Car Tire Pressure Flashlight

Car Alarm Keyless Entry System Central Control This is a universal car alarm system with remote central control function, keyless entry feature.It is widely used with all kind of cars. Feature: 1. Remotely lock and unlock your car 2. Direction light flashing 3. Electric/pneumatic central door lock optional 4. Central door lock automatically 5. Remote car location 6. Remote trunk release 7. Rising power window 8. Universal for most of cars Specification: Main unit Working Voltage: DC 12 3V Static Current: 8.5 mA Turning Light: 7.5 A x 2 Central Locking: 10A/433.92 Working Frequency: 315-316 433.92MHz Remote Control Working Voltage: DC 12V Average Static Current: 0 mA Control Box Size: 9.1 x 6.6 x 3.3 cm (L x W x H) Remote Controller Size: 6.4 x 3.5 x 1 cm (L x W x H) Net Weight: 184 g Package Weight: 256 g Color: Black Package Included: 1 X Control box 2 X Remote Controllers 1 X Set of Wire

Multi-function 4 In 1 Car Tires Pressure Table Detector Digital Barometer Function: 1, Flashlights, emergency use; 2, Tire pressure gauge, ensure the correct tire pressure, prevent puncture to ensure road safety; 3, Life-saving hammer, escape use; 4, Seat belt cutter quickly cut the seat belt, so that better ensure security Specifications: Model: HY-818C Operating temperature: 30-122 degrees Fahrenheit (0 to 50 degrees Celsius) Measuring range: 2 to 150PSI Measured error value: 1PSI Material: ABS + stainless steel 1. Measuring tire pressure when the car is idle. 2. Press the "ON" boot, it automatically resets the display "0.0." 3. The tire pressure gauge car tire valve gas nozzle is aligned and pressed into (you must first remove the tire valve cap) and can not leak, and maintained until a stable measured value after the release. 4. The measured value will be maintained for about 90 seconds, then turn off the display automatically. 5. Press (hold) "ON" button for 3 seconds to force shutdown. 6. This product has three kinds of pressure measurement units modes: PSI (pounds-force / square inch) BAR (bar) KPa (kPa) .KG / M3 repeatedly pressing the "ON" button to switch. Package Included: 1 X Multi-function 4 In 1 Car Tires Pressure Table Detector Digital Barometer

Auto Central Lock System Keyless Entry Remote Control Unit Descritpition: This is a universal car central lock system with 4 motors and remote controller. Supporting keyless engry of your car, without using a key to control the car lock status, more convenient ,more reliable. Features: 1. Waterproof remote design 2. Remotely lock and unlock your car 3. Electric/pneumatic central door lock optional 4. Central door lock automatically 5. Universal for any cars, applicable for the car that without central lock moel Specifications: Support: Direction lights flashing output Motor: With central door lock motors (4 actuators) Voltage Input: 12V Material: Hardward plasticType: Universal model Function: lock, unlock, car locator(search position) trunk release Package Include: 1 X Control box 2 X Remote Controllers 1 X Set of Wire 4 X Motors 1 X English Manual

12V Universal One Way Car Alarm System Car Remote Central Locking Description: Car Remote Control Keyless Enter System Special function: lock, unlock, car locator(search position),raise window signal output, trunk release(-) Direction lights flashing output Specification: 1. Door lock (press button "lock" once) 2. Door unlock (press button "unlock" once) 3. Car search 4. Raise window output Press button "lock" once, the lights flash once. the door will be locked, the window closer will output 30 seconds. 5. Remote trunk release (optional equipment) while the central door lock is unlocked, output signal for 1 second. 6. Electric and pneumatic door locks 7. Program transmitter Package Included: 1 X M602 One Way Car Alarm System Car Remote Central Locking

EL-50448 Auto Tire Pressure Monitor TPMS Activation Tool for GM General Motors Description: This model fit for G.M most kind of vehicles, equipped with a 315 or 433 MHz Tire Pressure Monitoring (TPM) system. This re-learn procedure can be performed by using special tool EL-50448. Applicale: 2001 Seville (VIN K) Service Manual 2002 Corvette (VIN Y) Service Manual 2003 DeVille (VIN K) Service Manual 2004 CTS (VIN D) Service Manual 2005 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) Service Manual 2006 CTS (VIN D) Service Manual 2008 Envoy, TrailBlazer, Ascender (VIN S/T) Service Manual 2009 XL-7 (VIN L) Service Manual 2010 Cruze Service Manual 2011 LaCrosse (China) Service Manual 2012 Optra, Viva (VIN J) Service Manual 2013 Volt (VIN R) (North America, Holden) Service Manual (3210) 2014 G.M models Note: We had made a list of applicable car as some examples, actually this model fit for GM sereies of car. Package Include: 1 X EL-50448 Device

Vehicle Alarm System Security Protect Keyless Entry Central Control Description: This is one way car alarm system supporting keyless entry and central contol function, it is easy and convenient to control your car locking system and protect your car safety. Feature: 1. Arming with sound 2. Disarming 3. Mute-arming 4. Vehicle locator/Panic/Overtaking/Emergency call (not startup Output current: signal light:7.5A*2, siren 10A, central lock 10A Coding: Learning code Voltage: 12+3V Static Current: <10mA( except indicator, sensor) Indicator Current <3mA intermittently Shock Sensor Current: <1mA Frequency: 315/433.92MHz Remote Control: Voltage: 12V/9V/6V Static Current: 0mA Battery: CR2016*3/9V/ CR2032*2/6V / 27A/12V Frequency: 315/433.92MHz Coding: Learning code Coding times: > 1 million Model Number: 8114 Package Included: 1 X Car Alarm 2 X Remote Controller 1 X User Manual

W03 4 inch Car HUD Head Up Display with OBD Interface LED Feature: 1. OBD cable connection. 2. Outstanding definition by using white light LED 3. Common USB port good for software upgrade 4. Great for reading with accurate big screen 5. Multiple function display and automatic power on & off 6. Time display function 7. Real humanity speaking and reminding 8. Time recording of driving and parking 9. Auto adjusting the brightness when light source changing 10. Auto matching the parameter when starting the vehicles. How to Install: 1. Place the mat to the front desk of the diver under the front windshield with adhesive surface. 2. Place the HUD on the mat, adjust the view angle and position and make sure your vision clear. 3. Connect the OBD cable with vehicle OBD16 diagnostic port. 4. Connect OBD 12 pin USB port with the host,when the host was powered on, the setting icon will light on. 5. Start the car, then HUD power on, system will play the voice at the same time, monitoring data output. How to Work: It is using optical reflection principle, reflect the important driving data to the front glass of the vehicle. This device are placed under the windscreen of the vehicle, via OBD cable to receive the vehicle ECU data, timely and accurate read the speed/rotation speed/fuel data and so on. Then, project it onto the front windshield so that drivers no need to look down and can be read real time. This device greatly improve the security and practicability. Because of this, when our HUD are put on sale it will got positive feedback. Technical Indicator: Ambient Temperature - 20 ~ + 80 Relative Humidity 10% ~ 95% Environmental Noise 60 db (A) Alarm Sound Level 30 db (A) Working Voltage 5V / 1.2A Voice Reminding Content Speed/Gear-change lever /Fatigue/Engine temperature/battery Display Content Voice/Speed/Engine rotational speed/Idle speed and instantaneous Fule consumption/Engine temperature/ battery voltage/Clock Product Size 106 * 68 * 18. 5 mm Product Weight 95 g Package Included: 1 X W03 Head Up Display 1 X OBD Line

I5 6 inch Car HUD Head Up Display OBDII Interface Feature: 1. Detecting car's OBDII interface automatically and all car with OBD II or EUOBD are OK, plug and play; 2. Car speed, engine speed, water temperature, voltage/ throttle position/ Ignition angle/ one-hundred-kilometer acceleration time, instant fuel consumption, average fuel consumption, mileage, fuel shortage reminding, engine faulty, shift reminding, etc. are displayed; 3. Normal display mode, high-speed display mode and automatic display mode are set by yourself; 4. Kilometers and miles are free to switch, which greatly facilitates the dashboard of British Standard; 5. 6 inches display area, easy to read; 6. Switch on and off automatically, HUD start when car starting HUD shutdown when the engine is turning off to protect the car battery effectively; at the same time, you can switch on and off HUD by Manually Shutdown to protect the battery safety; 7. Single-stage and four-stage overspeed alarm for driving safely; 8. Engine speed alarming so that you can shift timely to save fuel, also has a special significance for the novice; 9. Automatic and manual brightness adjustment mode, no dazzling; 10. Compass (this function is optional) the precise position, car does not get lost; Accurately determining the position and not get lost. Installation Instruction: 1. Make sure if your car complies with OBD II (or EU OBD) interface standard; 2. Open up the engine hood and look for the OBDII sticker. If there is a sticker of "OBDII CERTIFIED" then you can use our HUD. You can also check if your car have a diagnostic Interface(the vast majority of cars made in china after 2006 have the diagnostic Interface). 3. If your car has a diagnostic Interface of 16PIN(Figure 3) then plug the OBDII cable with the diagnostic Interface of 16PIN. 4. Put the non-slip mat on the relatively flat position of the car console. Then you put HUD on the non-slip mat and adjust HUD. 5. Reflective film can be attached to the front windshield above HUD so that you can read the parameters form the reflective film. Remarks: tips of sticking the reflective film A. Firstly spray some water on the position of sticking the reflective film; B. Remove the protective layer of the film, then attach to the corresponding position; C. Adjust the location, then use a small scraper or a smooth object to scrape the surface of the film; D. After a few minutes, the moisture will evaporate, then gently wipe off the water droplets and dust. 6. Power-on test You switch on HUD and HUD shows the current car voltage. Then HUD searches the car computer system. If HUD displays data, such as car speed, engine speed etc, it indicates that the product has been installed successfully. Technical Indicator: Ambient Temperature - 40 ~ + 80 Relative Humidity 10% ~ 95% Environmental Noise 60 db (A) Alarm Sound Level 30 db (A) Working Voltage 9V ~ 16VDC (12Vdc/400mA) Size 155 * 93 * 15.7 (mm) Product Weight 80g Package Included: 1 X I5 6 inch HUD Head Up Display

Universal Car Remote Auto Protection Vehicle Entry Security Burglar System Alarm Feature: 1. Remote arm / disarm 2. Remote vibration alarm with LED indicator flashing 4. Anti-hijacking 5. LED indicator status Specification: Voltage 15V Alarming range 100M Alarm mode power off automatically Package Included: 1 X Main Control Unit 2 X Remote Control 1 X Wiring Set 1 X User Manual

Universal Car Remote Control Central Kit Door Lock Locking Keyless Entry System Feature: -Remotely door lock/unlock -Outside pins for selecting lock/pneumatic lock -Light flashing output -Negative trunk release output optional -Power window output optional -Car locating -LED status indicator optional -Automatic central lock output optional -Siren optional -Universal for any cars have central locking. Specification: 1. Main Unit Color: Black Voltage:12 2V Coding: Learning code Output current: signal light - 5Ax2 siren - 10A central lock - 10A Static current: <15mA (except indicator, sensor) Indicator current: 20mA intermittently Shock sensor current: <1mA 2. Remote Control Voltage: 12V Current: 0mA Battery: 27A/12V Frequency: 300MHZ~433.92MHZ Coding: Learning Code Code Times: >million Note: 1. (IMPORTANT) No Instructions Included.Professional Installation Is Highly Recommended 2. Please check the size measurement chart carefully before making payment. 3. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 4. The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding. Package Included: 1 X Main Unit 2 X Remote Controllers 1 X Harness 1 X LED Connection Wire 1 X User Manual

0-200PSI Metal Digital Tire LCD Manometer Air Pressure Gauge PSI BAR KPA KGF/cm Featured: Intuitive digital display LCD screen display for easy reading. Used to monitor the tyre pressure, extending tire life and ensuring safety. High-end digital chip, LCD display monitor, testing more accurate, more reliable and cost-effective. When you are not using it,it will automatically switched off after 30 sec. Specification: Material: Copper+Rubber+Zinc alloy Size: 355x60mm Power supply: 2x Built-in CR2032 4 units available : PSI,KPa,Bar,Kgf/cm Note: 1. 1 KGF/cm = 98 KPA 2. Normal maintenance of the car should be measured tire pressure once a month. Package Included: 1 X Tire Pressure Gauge

Universal Car Auto Burglar Alarm Protection Security System Keyless 2 Remote Feature: 1. Multi-level security arming & high reliability and quality. 2. Can be used in different types of cars. 3. Equiped with 2 Remote Controls, a Siren and wiring harness, etc. Specification: Operating voltage: DC12V Quiescent Current: 8m Operating Frequency: 433.92MHZ Remote controller quantity: 2 Remote distance: 100 meters Size:as the below picture show Package Included: 1 X Main Control Unit 1 X Shock Sensor 1 X Siren 1 X LED Light 2 X Remote Control 1 X Set of Wiring Harness 1 X Instruction Manual

Universal 1 Way Car Security Alarm System w/2 Key Remote Controls Shock Sensor Feature: 1. Arm/Disarm; 2. Warning identification, Anti-hijacking; 3. Central door locking system automation; 4. Door unclosed well warning function; 5. Car finding,Re-arm; 6. Remote lock/unlock; 7. Automatic anti-theft warning; 8. Silent Arm;horn pause; 9. Over-taking warning; 10. Remote trunk release; 11. Emergency disarm, emergency call; 12. Hints for alarming; 13. ACC learning code; Specification: Main unit: 1. Voltage: 12V2V 2. Output current: signal light :5A*2;siren:10A, central lock:10A 3. Coding: learning code 4. Static current:<15mA 5. Indicator current:20mA 6. Shock Sensor current:<1mA 7. Operating frequency: 300MHz 350MHZ Remote controller 1. Voltage: 12V 2. Current: 0mA 3. Battery:27A/12V(Included) 4. Coding: learning code 5. Coding times:>1 million Package Included: 1 X Main Control Unit 2 X Remote Control 1 X LED Connection Wire 1 X Engine Killer Relay 1 X Shock Sensor 1 X Siren 1 X Wiring Set 1 X English User Manual

1 Way Car Security Alarm System w/2 Key Remote Controls Shock Sensor Universal Feature: 1. Arm/Disarm; 2. Warning identification, Anti-hijacking; 3. Central door locking system automation; 4. Door unclosed well warning function; 5. Car finding,Re-arm; 6. Remote lock/unlock; 7. Automatic anti-theft warning; 8. Silent Arm;horn pause; 9. Over-taking warning; 10. Remote trunk release; 11. Emergency disarm, emergency call; 12. Hints for alarming; 13. ACC learning code. Specification: Main Unit: 1. Voltage: 12V3V 2. Output current: signal light :7.5A*2;siren:10A, central lock:10A 3. Coding: learning code 4. Static current:10mA 5. Indicator current:3mA 6. Shock Sensor current:<1mA 7. Operating frequency: 315MHz-433.92MHZ Remote Controller: 1. Voltage: DC12V 2. Current: 0mA 3. Battery: CR2016(Included) Shock Sensor: 1.Voltage:DC123V 2.Static current:1mA Package Included: 1 X Main Control Unit 1 X LED Connection Wire 1 X Engine Killer Relay 1 X Shock Sensor 1 X Siren 1 X Wiring Set 2 X Remote Control 1 X English User Manua

Rear Left/Right Brake Pad Sensor Replacement For Range Rover Sport LR3 LR4 Specification: Color:Black Overall Size(approx.):121cm(L) (Detail size as shown in the picture) Material:Plastic Manufacturer Part Number:SOE000025 Other Part Number:SOE000025 Placement on Vehicle:Left, Right, Rear Feature: 1.It is durable and convenient. 2.Simple design and easy to use. Fitment:(The Compatibility Is Just For Reference. Please Compare The Follows With Your Original One before Purchasing.) Fit for 2006-2013 Land Rover Range Rover Sport 2010-2012 Land Rover LR4 2005-2009 Land Rover LR3 Note: 1.We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. 2.Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 3.The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding. 4.No Instructions Included.Professional Installation Is Highly Recommended. Package Included: 1 X Brake Pad Sensor

Car GPS Phone HUD Mobile Navigation Bracket Head Up Display HUD Projection Holder The Original Intention Of The Design: Nowadays the majority of people have taken advantage of a smart phone for navigation. Then a large number of mobile brackets have appeared attributed to its inconvenience to place. While there are such defects as inconvenient to grasp, uneasy to lower or raise head and tend to block sight among these mobile brackets, which make them not easy to use. So We Designed This Product: HUD mobile navigation bracket exploits the hardened organic glass to prevent scratch and project navigation information onto the panel based on optical reflection theorem. When placed on the center console, drivers need not bow to see because it will not block sight. Thus drivers could pay more attention the road conditions nearby. In the meanwhile, the design avoids the drivers observing the distant road conditions, which makes the navigation information more visualized and thereby improves the driving safety. Specification: Color Black Open Size 160 x 94.2 x 94mm Material ABS(Acrylonitrile Butadiene Styrene Copolymers) Plastic, Plexiglass, Silicone Compatible Model Fit For Devices Screen Size With 6.5'' HUD Angle About 198Can Be Adjustable Method Of Installation: 1.The above parts should be installed to the main body by pressing 2.Cleaning the surface on which is to be placed. It is generally recommend to clean the surface with dipped cloth. Then waiting for surface dry. 3.Jointing the base into the adhesive surface and exerting proper pressure to make the bonding effective after drying. 4.Putting the phone on the stents anti-skid mat and adjusting the organic glass board to appropriate angle according to individual visual angle. 5.HUD Mobile Navigation Bracket can be placed on the center console and the best visual angle is 45. Also can be adjusted according to individual preference. 6.Starting your car after opening the mobile navigation system and setting the proper route (now most of the navigation systems contain a reflection mode). Package Included: 1 X Holder 1 X Holder Base 1 X Silicone Mat 1 X Clean Cloth 1 X Set Protect Film 2 X User Guide Picture details:

E300 5.5 Inch Car HUD Head Up Display Apply for OBDII and EUOBD Feature: 1. Plug and Play connectivity with any OBDII or EUOBD capable vehicle 2. 2D visual effect 3. 5.5" screen 4. Multi color design makes the screen easier to read highlight important details for quick viewing; 5. The use of nanotechnology to eliminate unwanted reflections making the information easier to read; 6. Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time, mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometer/mile 7. Auto power on and off with the vehicle 8. Automatic and manual brightness adjustment mode Specification: Environment Temperature - 40 ~ +80 Barometric Press 86 ~ 106KPa Relative Humidity 10% ~ 95% Environment Noise 60dB Alarm Decibel 30dB(A) Work Voltage 9V ~ 16Vdc(12Vdc/400mA) Product Dimensions 12.5 * 7.5 * 1.5(cm) Product Weight 110g Package Included: 1 X E300 HUD